Deep Round Silicone Mold, 3 x 1.5, ULTRA Quality
Final Cast Dimensions: Diameter: 3" Depth: 1.5" Surface Finish: Smooth/Shiny/Glossy This listing is for a Deep Round Mold. The surface of this mold is glossy. Custom Sizes Available Upon Request! Please message us with any questions you may have regarding this mold. **Please note this listing is for the silicone mold ONLY. All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal) Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable
Final Cast Dimensions: Diameter: 3" Depth: 1.5" Surface Finish: Smooth/Shiny/Glossy This listing is for a Deep Round Mold. The surface of this mold is glossy. Custom Sizes Available Upon Request! Please message us with any questions you may have regarding this mold. **Please note this listing is for the silicone mold ONLY. All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal) Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys. SILICONE MOLD CARE INSTRUCTIONS • DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast. • Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles. • USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin. • Make sure the resin is fully. Uncured resin may rip the mold. • Please follow all safety precautions when using resin. It is very toxic. • Plastic Wrap/Bag Marks on trays will go away within 48-72 hours. • All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring. • If you have further questions or concerns about your mold, please shoot me a message on and I’ll get you taken care of. PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.
Log Cabin Silicone Mold for Candles, Soap, Crafts – Siligrams
Skull shape Cake Pan and Silicone Mini Cakes Skull Mold Wilton Halloween Cinco
Large Silicone Molds for Resin
Silikomart Silicone Bake Mold Waffle Shape .39 Oz, 1.5 Dia X .47h, 18 Cavities : Target
Reusable Charcuterie Board Silicone Molds
Silikomart Silicone Mini Cake Mold 3.7 Oz, 4-11/16 X 1-3/4 X 3/4 High, 6 Cavities : Target
Small round resin epoxy coaster mold Resin mold for coasters. Shapes of coaster tile or candle holder molds. Use with a wide range of edible and non edible materials, such as resin epoxy, uv resin, concrete, plaster, candle, soap, wax, isomalt, fondant. High resoluction transparent so you can check the buttom when process project. Mainly use for resin jewelry casting. Can mix uv resin or resin epoxy with types of clays ( such as polymer clay, air dry clay, resin clay etc.
Funshowcase Circle Coaster Resin Silicone Mold 3.5inch
Mini Cake Pop Mold – Bake Supply Plus
Large Deep Square Resin Mold Silicone Epoxy Resin - Temu
